Aluminum rad for a small block camaro,firebird fits 67 68 69 with a flex a lite electric fan.Perfect set up.Going LS1 so I need a different rad and dual fans.

Brand new never installed K1 bb mopar stroker crankshaft for a low deck engine 4.250 stroke with bb chevy rod jornals 650.00 905-384-2886

Small Block Chevy 1.7 Harland Sharp Roller Rockers. Full set of 16 for only 250.00. Please call 647-406-1147

Used Mopar Performance Large (7290)U-Joint pinion yoke. 10 spline. Fits "742" case 8 3/4 and 10 sline Dana 60 Cost $181 new Sell $100

Used Richmond 4.10 to 1 ring and pinion. Fits 8 3/4 with "742" case Excellent condition, were quite when removed. Cost $230 new sell for $100

SMC heads 882.s good cond. $175.00 2 Speed powerglide 65 good cond., with conv,dip stick,tube...$200.00 SBC..2chrome rocker covers,8 hold downs, 2 wire looms and 8 T style (bowtie)screw in .........$100.00 2" OFFY spacer............$30.00 Remote DUAL oil filter $80.00 8 GM powdwer rods...350..$100.00 Set of Screwin studs,guide plates $40.00

ELELBROCK CHOME LOW PROFILE VALVE COVERS FITS 260-289-302 NOT BOSS OR EFI BRAND NEW IN BOX PART#4460 $50.00 TAKE IT AWAY

CRANE ROCKER 11746-16 NEW $225.00 HOLLEY STREET DOMINATOR INTAKE CLEAN & GOOD SHAPE $100.00 EDELBROCK TORKER INTAKE CLEAN & GOOD SHAPE $100.00

I am now looking for a Holley Billet 125 fuel pump, not the Blue pump. Also need a good canister style filter. Thanks for looking.

SBF WEIAND INTAKE part # 2p 180 good shape 125.00

I have a fresh 850 Holley dp df just put a new kit in it and put is on the shelf 275.00

Have a holley BASE PLATE ONLY can be used on a 650, 700, 750, 800, double pumper carbs. Shipping is $10 in Canada and will take paypal

I need a Holley blue electric fuel pump, regulator not needed. Located in Mississauga thanks for looking.

FOR SALE IS A 850 RACE DEAMON CARB COMES WITH A FUEL LINE AND A ARMSTRONG SPACER ASKING $500 ALSO A 1150 HP DOMINATOR CARB ASKING $550 THESE CARBS ARE LIKE NEW PHONE 902-439-6573 THANKS

Aeromoive A1000 (Red) Fuel Pump for EFI (1000HP Forced Induction/ 1300HP NA). Rebuilt by Aeromotive. Upgraded to bigger pump so my spare needs to go.

8 eagle bushed i beam rods plus new bearings $140 new 7/16 stud girdle $90 MSD soft touch rev control with a 7000 chip $40

2 stock timing covers $10 each 1 2 peace timing cover $15 1 stock oil pan $20 1 stock 168 tooth fly wheel $20 1 stock starter $20

used ,good condition SBF 6.155 hardened pushrods part number on rods reads 48168 with Guides. Email or Call Ron 416-261-1053. Kingston Rd/Midland Ave Scarborough

have a custom 3800 stall, as well as 3:73 gears for a 10 bolt 8.5" rear end, gm gears in EXCELLENT condition.. asking 150 for the gears, and 400 for the stall ... please email or call after 4pm thanks rob

Good monring, I have a Holley 950 Hp part number 80496 that im selling. This carb if fresh and was just rebuilt for pinks last weekend. It will be coming off my 427 big block chev. Im looking to get $ 500.00 for this carb, it is flawless with no dissapointments. Reason for selling is im going to a dominator style carburator. Thanks Vito.

Complete Ford 9" Rear End Housing, 28 spline spool, 4:11 gears, 59 1/2" axle to axle. No backing plates or brakes. $650.00

Ford 9" 31 spline STRANGE spool and US GEAR 4:30 gears, complete in standard case. $350.00

ALUMINUM Hi-PERF Cyl HEADS BB CHEV...2 Versions..320cc RECT/Square Ports..OR..300cc OVAL Ports..SPECS..OPEN CHAMBER 115cc Combustion Chambers..BRONZE Guides..3 angle cut Hardened valve Seats..Extra THICK Decks resist warping & easily Milled to Increase Compression..Fit all OEM std Intake Manifold/Exhaust Header bolt patterns Plus THREADED bolt Holes for OEM BOLT-On Access/Brackets...COME WITH..STAINLESS STEEL BIG 2.250 Intake/1.88 Exhaust "Hi-FLOW" VALVES..Hi-LIFT/Hi-Perf Valve SPRINGS..Moly RETAINERS..Hardened Keepers..oil Seals..Screw-in Studs/Guide Plates...SELL..TWO Ways..COMPLETE w/ALL Parts Listed above w/Fully MACHINED Castings..READY to ASSEMBLE... $1259.99/Pair..."OR"..Professionally ASSEMBLED..READY to BOLT-ON...$1399.99/Pair...BRANT PERFORMANCE.

KIT "INCLUDES.....EAGLE 3.40" "STROKER" Crank...FORGED 5140 STEEL "I-BEAM" Connecting RODS....KEITH BLACK Flat Top "HYPERUTECTIC" PISTONS & MOLY RINGS...This KIT is "BALANCED" & INCLUDES Heavy Duty Harmonic BALANCER & FLEXPLATE.....ALL components are "NEW" & TOP QUALITY...$1099.99...Brant Performance..Your HI-PERF ENGINE PARTS SUPPLIER...Thanks.

Kit by EAGLE to fit 350 chev 2 pc seal blocks...INCLUDES FORGED 4340 STEEL "NITRATED" 3.500" LITE-WEIGHT STROKER Crank...FORGED 4340 STEEL "H-BEAM" LITE-WEIGHT 6.0" Rods with ARP Bolts...MAHLE Flat Top 10.5-1 FORGED 4.030 bore Pistons that are "THERMAL COATED"...This kit is "INTERNALLY BALANCED"....ALL Components are BRAND "NEW"..TOP QUALITY...$1299.99 or Will Sell CRANK & RODS Together as a SET for $999.99...Brant Performance...Your Hi-PERF ENGINE PARTS SUPPLIER !...Thanks.